Man Page

Manual Section... (7) - page: udplite

 

NAME

udplite - Lightweight User Datagram Protocol  

SYNOPSIS

#include <sys/socket.h>

sockfd = socket(AF_INET, SOCK_DGRAM, IPPROTO_UDPLITE);  

DESCRIPTION

This is an implementation of the Lightweight User Datagram Protocol (UDP-Lite), as described in RFC 3828.

UDP-Lite is an extension of UDP (RFC 768) to support variable-length checksums. This has advantages for some types of multimedia transport that may be able to make use of slightly damaged datagrams, rather than having them discarded by lower-layer protocols.

The variable-length checksum coverage is set via a setsockopt(2) option. If this option is not set, the only difference to UDP is in using a different IP protocol identifier (IANA number 136).

The UDP-Lite implementation is a full extension of udp(7), i.e., it shares the same API and API behaviour, and in addition offers two socket options to control the checksum coverage.  

Address Format

UDP-Litev4 uses the sockaddr_in address format described in ip(7). UDP-Litev6 uses the sockaddr_in6 address format described in ipv6(7).  

Socket Options

To set or get a UDP-Lite socket option, call getsockopt(2) to read or setsockopt(2) to write the option with the option level argument set to IPPROTO_UDPLITE. In addition, all IPPROTO_UDP socket options are valid on a UDP-Lite socket. See udp(7) for more information.

The following two options are specific to UDP-Lite.

UDPLITE_SEND_CSCOV
This option sets the sender checksum coverage and takes an int as argument, with a checksum coverage value in the range 0..2^16-1.

A value of 0 means that the entire datagram is always covered. Values from 1-7 are illegal (RFC 3828, 3.1) and are rounded up to the minimum coverage of 8.

With regard to IPv6 jumbograms (RFC 2675), the UDP-Litev6 checksum coverage is limited to the first 2^16-1 octets, as per RFC 3828, 3.5. Higher values are therefore silently truncated to 2^16-1. If in doubt, the current coverage value can always be queried using getsockopt(2).

UDPLITE_RECV_CSCOV
This is the receiver-side analogue and uses the same argument format and value range as UDPLITE_SEND_CSCOV. This option is not required to enable traffic with partial checksum coverage. Its function is that of a traffic filter: when enabled, it instructs the kernel to drop all packets which have a coverage less than the specified coverage value.

When the value of UDPLITE_RECV_CSCOV exceeds the actual packet coverage, incoming packets are silently dropped, but may generate a warning message in the system log.

 

ERRORS

All errors documented for udp(7) may be returned. UDP-Lite does not add further errors.  

BUGS

Where glibc support is missing, the following definitions are needed:

#define IPPROTO_UDPLITE     136
#define UDPLITE_SEND_CSCOV  10
#define UDPLITE_RECV_CSCOV  11
 

FILES

/proc/net/snmp - basic UDP-Litev4 statistics counters.
/proc/net/snmp6 - basic UDP-Litev6 statistics counters.  

VERSIONS

UDP-Litev4/v6 first appeared in Linux 2.6.20.  

SEE ALSO

udp(7), ip(7), ipv6(7), socket(7)

RFC 3828 for the Lightweight User Datagram Protocol (UDP-Lite)
Documentation/networking/udplite.txt  

COLOPHON

This page is part of release 3.21 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.


 

Index

NAME
SYNOPSIS
DESCRIPTION
Address Format
Socket Options
ERRORS
BUGS
FILES
VERSIONS
SEE ALSO
COLOPHON

This document was created by man2html, using the manual pages.
Time: 15:27:54 GMT, June 11, 2010

Leave a Reply

You must be logged in to post a comment.